PART NO. SPL.PAGE DESCRIPTION
1G752 15.A.2 Dowel for gearbox mounting plate (2) -(engine unit, 1500)
1G752 sup.1 Dowel -gearbox mouning plate (2) -(block assy, engine unit, sup)
1G752 16.A.1 Dowel -gearbox mouning plate (2) -(block assy, engine unit, 1600)-
New No. 1K151
1G752 16.A.21 Dowel -gearbox mouning plate (2) -(block assy, engine unit, 1600)-
New No. 1K151 -for 1G752 use 1K51 for this application
1G752 TC.A.1 Dowel for engine rear plate (2) -(cyl.block assy, engine, Twin Cam)
1G765 15.A.3 Bush for 1st motion shaft -(spigot bush, crankshaft, engine, 1500)
1G765 sup.3 Bush -1st motion shaft -(spigot bush, crankshaft, engine, sup)
1G765 16.A.3 Bush -1st motion shaft -(spigot bush, crankshaft, engine, 1600)
1G765 16.A.24 Bush -1st motion shaft -(spigot bush, crankshaft, engine, 1622)
1G765 TC.A.5 Bush for drive gear -(spigot bush, crankshaft, engine, Twin Cam)
1G1167 15.A.3 Restrictor -Oil (4) -(big end journal, crankshaft, engine, 1500)
1G1167 sup.3 Restrictor -Oil (4) -(big end journal, crankshaft, engine unit, sup)
1G1167 16.A.3 Restrictor -Oil (4) -(big end journal, crankshaft, engine unit, 1600)
1G1282 15.A.6 Plate -blanking -cylinder head side (heater valve)
1G1282 sup.6 Plate -blanking -heater outlet elbow -(cyl.head, engine unit, sup)
1G1282 16.A.6 Plate -heater outlet elbow blanking -(cyl.head, engine unit, 1600)
1G1282 16.A.27 Plate -heater outlet elbow blanking -(cyl.head, engine unit, 1622)
1G1309 TC.A.7 Clip for vent pipe -(side.cover, engine, Twin Cam) Com.(E)657 -was
11G80
1G1319 15.A.3 Washer for starting dog nut (lock) -(crankshaft, engine unit, 1500)
1G1319 sup.4 Washer -locking -starting nut -(crankshaft, engine unit, sup)
1G1319 16.A.4 Washer -lock -starting nut -(crankshaft, engine unit, 1600)
1G1319 16.A.25 Washer -lock -starting nut -(crankshaft, engine unit, 1622)
1G1361 15.A.3 Plate -camshaft locating -[Prev 1A2032, Fin.(E)GB258] -(Alt.no's)
1G1365 15.A.6 Joint -thermostat [Fin (E) GB17537]
1G1452 15.A.9 Valve -oil release -(engine unit, 1500)
1G1452 sup.9 Valve -oil release -(engine unit, sup)
1G1452 16.A.8 Valve -oil release -(engine unit, 1600)
1G1452 16.A.29 Valve -oil release -(engine unit, 1622)
1G1452 TC.A.13 Valve -oil release -(oil.pump, engine, Twin Cam)
1G1783 15.A.12 Fan for dynamo -(1500)
1G1783 TC.A.17 Fan for dynamo -(dist+dynamo mountings, engine, Twin Cam)
1G1989 15.A.8 Cover -oil strainer bottomn [Fin(E)GB46044 except 46101-46342]
1G2062 sup.11 Spindle -distributor driving -(dynamo +dist.mtg, engine unit, sup)
1G2062 16.A.11 Spindle -distributor driving -(dynamo +dist.mtg, engine unit, 1600)-
repl for 2A189 and 2A947
1G2062 16.A.25 Spindle -distributor driving -(dynamo +dist.mtg, engine unit, 1622)-
repl for 2A189 and 2A947
1G2285 15.A.4 Housing for distributor (to crankcase, engine unit, 1500)
1G2285 sup.11 Housing for distributor -(dynamo +distributor mtg, engine unit, sup)
1G2285 16.A.11 Housing -distributor -(engine unit, 1600)
1G2285 16.A.25 Housing -distributor -(engine unit, 1622)
1G2290 15.A.10 Joint washer -reservoir to crankcase -(engine unit, 1500)
1G2290 16.A.9 Joint washer -oil reservoir -(engine unit, 1600) - changed to 88G256
1G2290 TC.A.13 Joint -sump to crankcase -(sump, engine, Twin Cam)
1G2295 15.A.5 Bush for valve rocker -(cyl.head, engine unit, 1500)
1G2295 sup.6 Bush -valve rocker (8) -(cyl.head, engine unit, sup)
1G2295 16.A.5 Bush (8) -(valve rocker, cyl.head, engine unit, 1600)
1G2295 16.A.26 Bush -valve rocker (8) -(cyl.head, engine unit, 1622)
1G2301 15.A.11 Body -water pump [Fin(E)GB39864 except 39401-39525]
1G2302 15.A.11 Joint washer -water pump to block
1G2302 sup.11 Washer -joint -pump to crankcase -(pump assy 12H839, engine unit, sup)
1G2302 sup.11 Washer -joint -pump to crankcase -(w.pump rep.kit, 12H839 pump,
1G2302 16.A.11 Joint -water pump to crankcase -(w.pump 1H1149, engine unit 1600)
1G2302 16.A.31 Joint -water pump to crankcase -(w.pump 1H1149, engine unit 1622)
1G2303 15.A.11 Distance piece -gland(w-pump)[Fin(E)GB39864 except 39401-39525]
1G2310 15.A.11 Retainer -grease (w-pump) [Fin(E)GB39864ex39401-39525]
1G2316 sup.4 Nut -starting -(crankshaft, engine unit, sup)
1G2316 16.A.4 Nut -starting -(crankshaft, engine unit, 1600)
1G2331 15.A.2 Washer -thrust (upper)(2) -(crankshaft, engine unit, 1500)
1G2331 sup.3 Washer -thrust -upper (2) -(crankshaft, engine unit, sup)
1G2331_03 sup.3 Washer -thrust -upper -.003" (.0762mm) O/S (2) -(c-shaft, engine, sup)
1G2331 16.A.3 Washer -thrust (upper) (2) -(crankshaft, engine unit, 1600)
1G2331 16.A.24 Washer -thrust (upper) (standard) (2) -(crankshaft, engine unit, 1622)
1G233103 16.A.24 Washer -thrust (upper) .003" (.0762mm)o/s (2) -(c-shaft, engine, 1622)
1G2331 TC.A.5 Washer -thrust (upper) (standard) (2) -(crankshaft, Twin Cam)
1G233103 TC.A.5 Washer -thrust (upper) .003" (.0762mm)o/s (2) -(crankshaft, Twin Cam)
1G2332 16.A.24 Washer -thrust (lower) (standard) (2) -(crankshaft, engine unit, 1622)
1G233203 16.A.24 Washer -thrust (lower) .003" (.0762mm)o/s (2) -(c-shaft, engine, 1622)
1G2332 15.A.2 Washer -thrust (lower)(2) -(crankshaft, enggine unit, 1500)
1G2332 sup.3 Washer -thrust -lower (2) -(crankshaft, engine unit, sup)
1G2332_03 sup.3 Washer -thrust -lower -.003" (.076mm) O/S (2) -(c-shaft, engine, sup)
1G2332 16.A.3 Washer -thrust (lower)(2) -(crankshaft, engine unit, 1600)
1G2332 TC.A.54 Washer -thrust (lower) (standard) (2) -(crankshaft, engine, Twin Cam)
1G2332_03 TC.A.54 Washer -thrust -lower -.003" (.076mm) O/S (2) -(crankshaft, engine,
Twin Cam)
1G2340 15.A.3 Gear -camshaft [Fin (E) GB258]
1G2342 15.A.6 Joint washer for blanking plate (heater valve)
1G2342 15.A.8 Joint washer -strainer [Fin(E)GB46044 except 46101-46342]
1G2342 sup.6 Washer -joint -blanking plate -(htr.valve, cyl.head, engine unit, sup)
1G2342 16.A.6 Joint washer -blanking plate -(htr.valve, cyl.head, engine unit, 1600)
1G2342 16.A.27 Joint washer -blanking plate -(htr.valve, cyl.head, engine unit, 1622)
1G2367 15.A.3 Connecting rod and cap for Nos. 2 and 4 cyl's [Fin (E) GB8569]
1G2370 15.A.3 Connecting rod and cap for Nos. 1 and 3 cyl's [Fin (E) GB8569]
1G2380 15.A.4 Push-rod [Fin (E) GB5503]
1G2385 15.A.8 Pipe -oil strainer suction [Fin (E)GB46044 except 46101-46342]
1G2390 15.A.8 Strainer -oil [Fin (E) GB46044 except 46101-46342]
1G2391 15.A.8 Body -oil strainer [Fin (E)GB46044 except 46101-46342]
(alt 11G143)
1G2393 15.A.7 Plate -engine monting (front) [Fin (E) GB258]
1G2394 15.A.7 Joint -mounting plate to crankcase [Fin (E) GB258]
1G2398 15.A.4 Oil seal for pinion (tachometer drive, engine unit, 1500)
1G2398 sup.7 Seal -oil -pinion -(tachometer drive, engine unit, sup)
1G2398 16.A.7 Oil seal -pinion -(tachometer drive, engine unit, 1600)
1G2398 16.A.28 Oil seal -pinion -(tachometer drive, engine unit, 1622)
1G2398 TC.A.17 Oil seal for pinion -(tachometer drive, dist+dynamo mountings,
engine, Twin Cam)
1G2399 15.A.4 Retaining ring (oil seal for tach drive pinion, engine unit, 1500)
1G2399 sup.7 Ring -retiining -(oil seal for tach drive pinion, engine unit, sup)
1G2399 16.A.7 Ring -oil seal retaining -(tach drive pinion, engine unit, 1600)
1G2399 16.A.28 Ring -oil seal retaining -(tach drive pinion, engine unit, 1622)
1G2399 TC.A.17 Ring -seal retaining -(seal, tach.drive, dist+dynamo mountings,
engine, Twin Cam)
1G2401 15.A.4 Joint washer for housing (tach drive, engine unit, 1500)
1G2401 sup.7 Washer -joint -housing -(tach drive, engine unit, sup)
1G2401 16.A.7 Joint -tachometer pinion housing -(engine unit, 1600)
1G2401 16.A.28 Joint -tachometer pinion housing -(engine unit, 1622)
1G2401 TC.A.17 Joint for housing -(tach.drive, dist+dynamo mountings, engine, Twin
Cam)
1G2417 15.A.16 Joint washer manifolds to cylinder head -(engine unit 1500)
1G2417 16.A.15 Joint washer manifolds to cylinder head -(engine unit 1600)
1G2418 15.A.16 Yoke -manifold (4) -(very heavy steel washer, engine unit 1500)
1G2418 16.A.15 Yoke -manifolds (4) -(very heavy steel washer, engine unit 1600)
1G2425 15.A.7 Joint -rear mounting (engine)
1G2425 sup.8 Washer -joint -mounting plate -(rear, engine unit, sup)
1G2425 16.A.7 Joint -mounting plate to crankcase -(rear, engine unit, 1600)
1G2425 16.A.28 Joint -mounting plate to crankcase -(rear, engine unit, 1622)
1G2425 TC.A.6 Joint -plate to crankcase -(rear, engine.mtg.plate, engine, Twin Cam)
1G2443 15.A.7 Plate -blanking -petrol pump face [Fin (E) GB51767]
1G2443 sup.1 Plate -blanking -petrol pump -(block assy, engine unit, sup)
1G2443 TC.A.1 Plate -blanking -(fuel pump port, cyl.block assy, engine, Twin Cam)
1G2444 15.A.7 Joint for petrol pump blanking plate [Fin (E) GB51767]
1G2444 sup.1 Washer -joint -petrol pump blanking plate -(block assy, eng.unit, sup)
1G2444 TC.A.1 Joint for plate -(fuel pump port, cyl.block assy, engine, Twin Cam)
1G2508 15.A.10 Reservoir -oil -(engine unit, 1500)
1G2508 16.A.9 Reservoir -oil -(engine unit, 1600) - changed to 12H395
1G2522 15.A.5 Shaft assembly -valve rocker -(cyl.head, engine unit, 1500)
1G2522 sup.6 Shaft assembly -valve rocker -(cyl.head, engine unit, sup)
1G2522 16.A.5 Shaft assembly -valve rocker -(cyl.head, engine unit, 1600)
1G2522 16.A.26 Shaft assembly -valve rocker -(cyl.head, engine unit, 1622)
1G2602 16.A.7 Clip for pipe -(crankcase vent, engine unit, 1600)
1G2602 16.A.28 Clip -pipe -(crankcase vent, engine unit, 1622)
1G2613 15.N.4 Box -fuse -(switches, 1500)
1G2613 16.N.4 Box -fuse -(switches, 1600 and 1600-MK-II)
1G2613 TC.N.4 Box -fuse -(switches, electrical, Twin Cam)
1G2620 15.B.1 Bracket -steady plate/dynamo -(ignition coil,1500) -Changed to 1H1070
-Com.(E)GB29710
1G2673 15.B.1 Four-way spacer -cables (for HT wires)
1G2716 15.A.12 Belt for fan (wedge type) -changed to 1H1001 Com. (E) GB17061
1G2716 16.A.13 Belt -fan -(engine unit, 1600) Com.(E)16GA/H6276 -(was 1H1001)-
1G2716 cor. was 1H2716 -not available use 13H923
1G2874 15.A.4 Ring -starter gear -(flywheel, engine unit, 1500)
1G2874 sup.4 Gear -ring -starter -(flywheel, engine unit, sup)
1G2874 16.A.4 Gear -ring -starter -(flywheel, engine unit, 1600)
1G2874 16.A.25 Gear -ring -starting -Not U.K. -(flywheel, engine unit, 1622)
1G2874 TC.A.5 Ring -starter -(flywheel, engine, Twin Cam)
1G2882 15.A.5 Guide -inlet valve [Fin (E) GB23174 but also 23201 to 23447]
1G2953 15.A.6 Plug for thermal transmitter boss
1G2953 sup.6 Plug -thermal transmitter boss -(cyl.head, engine unit, sup)
1G2953 16.A.6 Plug -thermal transmitter boss -(cyl.head, engine unit, 1600)
1G2953 16.A.27 Plug -thermal transmitter boss -(cyl.head, engine unit, 1622)
1G2984 15.A.4 Dowel -clutch to flywheel -(engine unit, 1500)
1G2984 sup.4 Dowel -clutch to flywheel (2) -(engine unit, sup)
1G2984 16.A.4 Dowel -clutch to flywheel (2) -(engine unit, 1600)
1G2984 16.A.25 Dowel -clutch to flywheel (2) -(engine unit, 1622)
1G3268 15.F.3 Peg for thrust washer -front (3rd gear)
1G3268 16.F.3 Peg -thrust washer -(front, 3rd gear, gearbox, 1600 and
1600-MK-II)
1G3268 TC.F.3 Peg -front thrust washer -(3rd gear, gearbox, Twin Cam)
1G3331 15.F.4 Ring -interlocking -2nd and 3rd gear bushes
1G3331 16.F.3 Ring -2nd and 3rd gear bushes -interlocking -(gearbox, 1600 and
1600-MK-II)
1G3331 TC.F.4 Ring -interlocking -(2nd-3rd gear bushes, gearbox, Twin Cam)
1G3418 15.F.1 Bush (gearbox rear, early and mid 1500) -Fin.(E)GB51767
1G3492 15.F.3 Washer -thrust -rear (3rd motion shaft)
1G3492 TC.F.3 Washer -thrust -rear (3rd motion shaft) -(gearbox, Twin Cam)
1G3530 15.F.3 Peg -locating (for gearbox center bearing housing)
1G3530 16.F.2 Peg -locating -rear bearing housing -(gearbox, 1600 and 1600-MK-II)
1G3530 TC.F.3 Peg -locating -(3rd motion bearing housing, gearbox, Twin Cam)
1G3576 15.F.4 Washer -thrust -front (for layger (A/R) -(gearbox, 1500)
1G3576 16.F.3 Washer -thrust -front -layger (A/R) -(gearbox, 1600 and 1600-MK-II)
1G3576 TC.F.4 Washer -thrust -front -layger (A/R) -(layger, gearbox, Twin Cam)
1G3577 15.F.4 Washer -thrust -rear, 0.155 thick (for layger) -(gearbox, 1500)
1G3577 16.F.3 Washer -thrust-rear .154" to .156" (3.912-3.962mm)(A/R) -(gearbox,
1600 and 1600-MK-II) -alternatives: 1G3577, 1G35778, 1G3579, 1G3580
1G3577 TC.F.4 Washer -thrust-rear .154" to .156" (3.912-3.962mm)(A/R) -(gearbox,
Twin Cam)
1G3578 15.F.4 Washer -thrust -rear, 0.157 thick (for layger) -(gearbox, 1500)
1G3578 16.F.3 Washer -thrust-rear .157" to .158" (3.988-4.013mm)(A/R) -(gearbox,
1600 & 1600-MK-II) -alternatives: 1G3577, 1G35778, 1G3579, 1G3580
1G3578 TC.F.4 Washer -thrust-rear .157" to .158" (3.988-4.013mm)(A/R) -(gearbox,
Twin Cam)
1G3579 15.F.4 Washer -thrust -rear, 0.160 thick (for layger) -(gearbox, 1500)
1G3579 16.F.3 Washer -thrust-rear .160" to .161" (4.060-4.085mm)(A/R) -(gearbox,
1600 & 1600-MK-II) -alternatives: 1G3577, 1G35778, 1G3579, 1G3580
1G3579 TC.F.4 Washer -thrust-rear .160" to .161" (4.060-4.085mm)(A/R) -(gearbox,
Twin Cam)
1G3580 15.F.4 Washer -thrust -rear, 0.163 thick (for layger) -(gearbox, 1500)
1G3580 16.F.3 Washer -thrust-rear .163" to .164" (4.136-4.162mm)(A/R) -(gearbox,
1600 & 1600-MK-II) -alternatives: 1G3577, 1G35778, 1G3579, 1G3580
1G3580 TC.F.4 Washer -thrust-rear .163" to .164" (4.136-4.162mm)(A/R) -(gearbox,
Twin Cam)
1G3581 15.F.4 Screw, locking for shaft (reverse gear, gearbox, 1500)
1G3581 16.F.3 Screw -reverse shaft -(gearbox, 1600 and 1600-MK-II)
1G3581 TC.F.4 Screw -locking -(reverse shaft, gearbox, Twin Cam)
1G3582 15.F.4 Bush for lever (clutch withdrawl) -Change to 11G3195 Com.(E)4525
1G3584 15.F.3 Nut for shaft (front of 1st motion shaft)
1G3584 16.F.2 Nut -1st motion shaft -(gearbox, 1600 and 1600-MK-II)
1G3584 TC.F.3 Nut for motion shaft -(1st motion, gearbox, Twin Cam)
1G3586 15.F.3 Housing -bearing (3rd motion shaft, center bearing)
1G3586 16.F.2 Housing -rear bearing (3rd motion shaft) -(gearbox, 1600 and
1600-MK-II)
1G3586 TC.F.3 Housing -bearing -(3rd motion, gearbox, Twin Cam)
1G3594 15.F.4 Gear -3rd speed -(gearbox, 1500)
1G3594 16.F.3 Gear -3rd speed -(gearbox, 1600 and 1600-MK-II)
1G3594 TC.F.4 Gear -3rd speed -(gearbox, Twin Cam)
1G3597 15.F.4 Synchronizer for 3rd and 4th speed -(gearbox, 1500)
1G3597 16.F.3 Synchronizer -3rd and 4th speed -(gearbox, 1600 and 1600-MK-II)
1G3597 TC.F.4 Synchronizer -3rd-4th speed -(gearbox, Twin Cam)
1G3598 15.F.4 Coupling -sliding -3rd-4th speed -(gearbox, 1500)
1G3598 TC.F.4 Coupling -sliding -3rd-4th speed -(gearbox, Twin Cam)
1G3611 15.F.3 Shaft -1st motion -(gearbox assy, 1500)
1G3611 16.F.1 Shaft -1st motion -(gearbox assy, 1600 and 1600-MK-II)-
Com.(E)16GC/H3929 also 3854
1G3611 TC.F.3 Shaft -1st motion -(gearbox, Twin Cam)
1G3612 15.F.3 Lock tab washer -Changed to 11G3226 Com.(G)A101 -
Changed to LWZ212 Com.(E)GD101
1G3613 15.F.3 Nut for shaft and speedometer gear -Change to 11G3225 Com.(G)A101 -
Change to FNZ612 Com.(E)GD101
1G3639 15.F.3 Distance piece -speedometer gear -Change to 11G3223 Com.(G)A101
1G3642 15.F.1 Cover -front (gearbox) -change to 11G3197 Com.(G)A4378
1G3653 15.F.4 Lever assembly -clitch withdrawl -change to 11G3193 Com.(E)4525
1G3656 15.F.1 Cover -side (gearbox) -(GB assy, 1500)
1G3656 16.F.1 Cover -gearbox side -(GB assy, 1600 and 1600-MK-II)
1G3656 TC.F.1 Cover side -(gearbox assy, Twin Cam)
1G3658 15.F.1 Joint for side cover (gearbox, 1500)
1G3658 16.F.1 Joint washer -side cover to casing -(GB assy, 1600 and 1600-MK-II)
1G3658 TC.F.1 Joint -side cover -(gearbox assy, Twin Cam)
1G3666 15.F.1 Joint for front cover (gearbox, 1500)
1G3666 16.F.1 Joint washer -front cover to casing -(GB assy, 1600 and 1600-MK-II)
1G3667 15.F.1 Dust cover -clutch withdrawl lever
1G3667 16.F.4 Cover -clutch withdrawl lever (dust) -(gearbox, 1600 and
1600-MK-II)
1G3667 TC.F.1 Dust cover -clutch withdrawl lever -(gearbox assy, Twin Cam)
1G3668 15.F.2 Breather assembly (gearbox) -Changed to 1H3364 Com.(E)GD101
1G3668 15.H.1 Breather assembly (rear axle)
1G3668 16.F.1 Breather assembly -(gearbox assy, Twin Cam)
1G3668 TC.H.1 Breather assembly -(rear axle, Twin Cam) -changed to 1H3364
1G3680 15.F.2 Lever -selector -front (selector shaft)
1G3680 16.F.4 Leaver -selector -front -(gearbox, 1600 and 1600-MK-II) -changed to
88G254
1G3680 16.F.2 Leaver -front selector -(gearbox assy, Twin Cam) -alternate 22H24
1G3682 15.F.2 Shaft -remote control (selector shaft)
1G3685 15.F.2 Block -shaft locating (gearbox) -changed to 11G3187 Com.(G)A916
1G3686 15.F.3 Selector -1st and 2nd gear -Changed to 11G3132 Com.(G)A290
1G3687 15.F.3 Selector -3rd and 4th gear -Changed to 11G3133 Com.(G)A290
1G3688 15.F.3 Selector -reverse gear -Changed to 11G3131 Com.(G)A290
1G3690 15.F.2 Fork -3rd and 4th speed -Changed to 1H3257 Com.(G)2A290
1G3691 15.F.2 Fork -1st and 2nd speed -Changed to 11G3135 Com.(G)2A290
1G3692 15.F.2 Shaft -3rd-4th speed fork -Changed to 11G3140 Com.(G)A290
1G3704 15.F.4 Bush for rear selector lever (split bronze, gearbox, 1500)
1G3704 16.F.5 Bush -change speed lever (split, gearbox, 1600 and 1600-MK-II)
1G3704 TC.F.4 Bush -rear selector lever -(split, gearbox, Twin Cam)
1G3706 15.F.5 Knob for change speed lever -(gearbox, 1500)
1G3706 16.F.4 Knob -change speed lever -(gearbox, 1600 & 1600-MK-II)
1G3706 TC.F.6 Knob -change speed lever -(gearbox, Twin Cam)
1G3708 15.F.3 Screw for selector locating (1st-2nd gear) -(gearbox, 1500)
1G3708 15.F.3 Screw for selector locating (3rd-4th gear) -(gearbox, 1500)
1G3708 15.F.3 Screw for selector locating (reverse gear) -(gearbox, 1500)
1G3708 16.F.2 Screw -selector locating (1st-2nd gear) -(gearbox, 1600 & 1600-MK-II)
1G3708 16.F.2 Screw -selector locating (3rd-4th gear) -(gearbox, 1600 and
1600-MK-II)
1G3708 16.F.2 Screw -selector locating (reverse gear) -(gearbox, 1600 and
1600-MK-II)
1G3708 TC.F.2 Screw -selector locating -(1st-2nd, gearbox, Twin Cam)
1G3708 TC.F.3 Screw -selector locating -(3rd-4th, gearbox, Twin Cam)
1G3708 TC.F.3 Screw -selector locating -(reverse, gearbox, Twin Cam)
1G3709 16.F.5 Circlip -bush -(change speed lever, gearbox, 1600 and 1600-MK-II)
1G3709 TC.F.4 Circlip -lever bush -(split, gearbox, Twin Cam)
1G3711 15.F.5 Joint for control tower (shift remote control, gearbox, 1500)
1G3711 16.F.5 Gasket -control tower -(remote tower, gearbox, 1600 and 1600-MK-II)
1G3711 TC.F.6 Joint -control tower -(remote tower, gearbox, Twin Cam)
1G3712 15.F.1 Joint for extension to gearbox -(GB assy, 1500)
1G3712 16.F.1 Joint washer -extension to casing -(GB assy, 1600 and 1600-MK-II)
1G3712 TC.F.1 Joint -extension to gearbox -(gearbox assembly, Twin Cam)
1G3713 15.F.5 Dowel for reverse plunger (remote control tower)
1G3713 16.F.4 Dowel -reverse plunger -(remote tower, gearbox, 1600 and 1600-MK-II)
1G3713 TC.F.6 Dowel -reverse plunger -(remote tower, gearbox, Twin Cam)
1G3802 15.F.1 Dipstick (gearbox)
1G3802 16.F.4 Oil level indicator -gearbox -(gearbox, 1600 and 1600-MK-II)
1G3802 TC.F.1 Dipstick -(gearbox assy, Twin Cam)
1G3804 15.F.1 Felt (for gearbox dipstick)
1G3804 TC.F.1 Felt -(for dipstick, gearbox assy, Twin Cam)
1G3809 15.F.2 Cover -extension side (gearbox top cover) -(gearbox assy, 1500)
1G3809 16.F.1 Cover -rear extension -side (gearbox top cover) -(GB assy, 1600 and
1600-MK-II)
1G3809 TC.F.1 Cover -extension -side (top cover) -(gearbox assy, Twin Cam)
1G3810 15.F.2 Joint for extension side cover (gearbox top cover)
1G3810 16.F.1 Joint washer -side cover to extension (gearbox top cover) -(GB assy,
1600 and 1600-MK-II)
1G3810 16.F.1 Joint -extensipn side cover (top cover) -(gearbox assy, Twin Cam)
1G3863 15.F.5 Spring for reverse plunger (remote control tower, gearbox, 1500)
1G3863 16.F.4 Spring -reverse plunger -(remote tower, gearbox, 1600 and 1600-MK-II)
1G3863 TC.F.6 Spring -reverse plunger -(remote tower, gearbox, Twin Cam)
1G3866 TC.F.1 Joint -front cover assembly -(gearbox assy, Twin Cam)
1G3927 15.F.5 Cover for ball spring (speed change lever hold down)
1G3927 16.F.4 Cover -ball spring (speed change lever hold down, gearbox, 1600 and
1600-MK-II)
1G3927 TC.F.6 Cover -ball spring -(speed change lever hold down, gearbox, Twin Cam)
1G4359 15.K.1 Stud -wheel (front hubs disc wheels) (8)
1G6368 16.H.1 Breather assembly -(rear axle, 1600 and 1600-MK-II) -changed to 1H3364
1G7372 16.S.1 Key -rear axle drain plug -(tool kit, 1600 and 1600-MK-II)-
Fin.(C)93547
1G7305 15.H.1 Washer for locknut (tab) -change to 1G7584 Com.(C)10917
(disc wheels), C)11450 (wire wheels) 1G7372 15.S.1
1G7372 15.S.1 Key -rear axle drain plug -(tool kit, 1500)
1G7372 TC.S.1 Key -rear axle drain plug -(tool kit, Twin Cam)
1G7430 16.H.2 Cover -dust -(differential pinion, rear axle, 1600 & 1600-MK-II)
1G7433 15.H.2 Hub assembly -rear (disc wheels only)(2) -(rear axle, 1500)
1G7435 15.H.2 Stud for wheel (disc wheels only)(8) -(rear axle, 1500)
1G7435 16.H.2 Stud -wheel (disc wheels only)(8) -(rear axle, 1600 and 1600-MK-II)-
part no. change was ATB7074 and BTB415
1G7436 15.H.2 Spacer for bearing (disc wheels only)(2) (rear hub, rear axle, 1500)
1G7436 16.H.2 Spacer -bearing (disc wheels only)(2) -(rear hub, rear axle, 1600 and
1600-MK-II)
1G7439 15.H.1 Dust cover for oil seal (differential front, rear axle, 1500)
1G7439 16.H.6 Cover -dust -(differential front, rear axle, ARDB model, 1600 and
1600-MK-II) -Com.(C)91240
1G7439 TC.H.2 Cover -dust -(differential front, rear axle, Twin Cam)
1G7444 15.H.1 Pin for pinion -(differential, rear axle, 1500)
1G7444 16.H.1 Pin for pinion -(differential, rear axle, 1600 and 1600-MK-II)
1G7444 16.H.5 Pin -pinion -(differential, rear axle, ARDB model 1600 and
1600-MK-II) -Com.(C)91240
1G7444 TC.H.1 Pin for pinion -thrust -(rear axle, Twin Cam)
1G7445 15.H.1 Washer -thrust -for pinion (2) (differential, rear axle, 1500)
1G7445 16.H.1 Washer -thrust -differential pinion (2) -(rear axle, 1600 and
1600-MK-II
1G7445 16.H.5 Washer -thrust -differential pinion (2) -(rear axle, ARDB model 1600
and 1600-MK-II) -Com.(C)91240
1G7445 TC.H.1 Washer for pinion -thrust (2) -(rear axle, Twin Cam)
1G7448 15.H.1 Locknut (R.H.T.) (2/1) -(rear axle, 1500) -Quantity reduced at
(C)10917 (disc wheels), (C)11450 (wire wheels
1G7448 16.H.1 Nut -bearing retaining (RHT) -(rear axle, 1600 and 1600-MK-II)
1G7448 16.H.5 Nut -bearing retaining (RHT) -(rear axle, ARDB model, 1600 and
1600-MK-II) -Com.(C)91240
1G7448 TC.H.1 Nut -bearing retaining (RHT) -(rear axle, Twin Cam)
1G7465 15.H.1 Joint for carrier to case -(rear axle, 1500)
1G7465 16.H.1 Joint -gear carrier to axle case -(rear axle, 1600 and 1600-MK-II)
1G7465 16.H.5 Joint -gear carrier to axle case -(rear axle, AWDB model, 1600 and
1600-MK-II) Com.(C)91240
1G7465 16.F.1 Joint -gear carrier to axle case -(rear axle, Twin Cam)
1G7582 15.H.1 Locknut (L.H.T.) (1) -Com.(C)10917 (disc wheels),
(C)11450 (wire wheels)
1G7582 16.H.1 Nut -bearing retaining (LHT) -(rear axle, 1600 and 1600-MK-II)
1G7582 16.H.5 Nut -bearing retaining (LHT) -(rear axle, ARDB model, 1600 and
1600-MK-II) -Com.(C)91240
1G7582 TC.H.1 Nut -bearing retaining (LHT) -(rear axle, Twin Cam)
1G7584 15.H.1 Washer for locknut (tab) -(rear axle, 1500) -Com.(C)10917
(disc wheels), (C)11450 (wire wheels) -(was 1G7305)
1G7584 15.H.1 Washer lock -bearing retaining nut (2) -(rear axle, 1600 & 1600-MK-II)
1G7584 16.H.5 Washer lock -bearing retaining nut (2) -(rear axle, ARDB model, 1600
and 1600-MK-II) -Com.(C)91240
1G7584 TC.H.1 Washer for bearing retaining nut (2) -(rear axle, Twin Cam)
1G7593 15.G.1 Dust cover -Com.(C)20753 (mid 1500 propshaft) -
Fin.(C)61037-61504 (interspersed)
1G7600 16.H.1 Washer -bearing packing .010" (.254mm)(A/R) (differential, rear axle,
1600 and 1600-MK-II)
1G7600 16.H.5 Washer -bearing packing .010" (.254mm)(A/R) (differential, rear axle,
ARDB model 1600 and 1600-MK-II) -Com.(C)91240
1G7600 TC.F.1 Washer -bearing packing .010" (.254mm)(A/R) -(differential, rear axle,
Twin Cam)
1G8492 16.F.3 Washer -thrust -3rd motion shaft -rear -(gearbox, 1600 & 1600-MK-II)
1G8598 16.F.3 Coupling -sliding -3rd and 4th speed -(gearbox, 1600 and 1600-MK-II)
1G8709 15.F.4 Circlip for lever bush (split bronze bush)
1G9198 16.M.5 Plate -locking (2) -(brake hose front, hyd.pipes +fittings, std.model
1600 and 1600-MK-II)
1G9840 16.R.20 Bolt -corner bar to center bar (2) -(front bumper assy, 1600 and
1600-MK-II)
1G9840 16.R.20 Bolt -mainspring to corner bar (2) -(front bumper assembly, 1600 and
1600-MK-II) -was AHH5480
1G9840 TC.R.20 Bolt -corner bar to center bar (2) -(front bumper assembly, Twin Cam)-
was AHH5491
1G9872 16.R.21 Bolt -mainspring to bar (outer) (2) -(rear bumper assembly, 1600 and
1600-MK-II) -was AHH5480
1G9872 TC.R.20 Bolt -spring bar to corner bar (2) -(front bumper assembly, Twin Cam)-
part number change was AHH5480
1G9872 TC.R.21 Bolt -spring bar to bumper bar (outer) (2) -(rear bumper assembly,
Twin Cam) -part number change was AHH5480
|
